Here is a summary of problems and obstacles which tend Computer Users How to Confront and Prevention Here I would invite my friend to know, what and why that caused computer pal damaged.There 24 ways that may often occur on our computers each of these solutions masing.mungkin : see ok ..
1. Computers Not Want to Live
The fix:
- Check cable connection (from the power outlet to the power button on PC)
- Check whether the stabilizer function or tdak (if using the stabilizer)
- Check the power cable on CPU
- If you still do not want to live problem may lie in the power supply or MB
2. Computer Life But Not want Booting
The fix:
Know First Beep Beep:
Beep 1 time only sign that the condition of good computer
Beep 1 time, length There are problems in memory
Beep 1 time and 3 times the short-term damage on the VGA card
Beep 1 time 2 times long and short-Damage in DRAM parity
Beep continuously Damage dimodul memory or video memory
- Check with using software such as SiSoft Sandra dianosa, PC mark04, mark05 PC etc.
3. Computer Mau Booting But Always "Safe Mode" (to go into safe mode press F8)
The fix:
- Restart your computer again
- If still trouble re intall your windows
- If it still safe mode also means your HD problems
check with: scan disk
4. Computer Hangs Frequently
How to cope
- Due to software crashes
- Press ctrl + alt + del>> click End Task on the program "Not Responding"
- Press the restart button on the CPU
- Due to hardware conflict (to the addition of new hardware)
- Conflicts between hardware often occurs on windows operating system
- Re-install your windows, but keep in mind before you reinstall windows, first remove your new hardware
- Run facilities "add new" hardware found on the control panel.
5. Keyboard is not recognized by Computer
How to cope
- Check if your keyboard is properly installed
- If it already but still the keyboard is not detected then chances are your keyboard problem.
- Try to replace your keyboard, if it has been replaced but the problem persists then most likely destroyed was at the keyboard port on your MB.
- If it has been in New Keyboard Replace remain undetected but Also Try to Replace with a USB keyboard and if not detected also means there is something wrong in the Windows system Buddies
6 Mouse is not recognized by the computer (the same case With keyboard)
7. Always Jumping Mouse Pointer-Skip
How to cope
- Clean up immediately on the dirty mouse (especially on the ball mouse)
8. Computer Crashes Often
The fix:
- Check all the cable position, hardware, and also stresses on the casing, check the temperature on the CPU and likewise check ram, processor and vga.
9. If Manufacturer MetherBoard (MB) Unknown
The fix:
- Open the casing, and check your CPU is usually a MB has a label manufacturer that also contains a specification type Mb.
- Look in the manual book
- Find a Mb of data over the Internet, skewer ID which is printed on the sticker board with list contained on the site www.fcc.gov / oet / fccid, and search the list of ID numbers issued by the licensing agency for electronic device in America
- Use analysis software, such as sandra99 etc.
10. Forgot BIOS Password
The fix:
- Remove the cmos on the cpu batterey
- Or by try some guessed default passwords for some manufacturers eg AMI and AWARD BIOS (eg, AMI, AMI, AMI_SW, Ally, 589 589 etc.)
11. Clock and setting the date BIOS Always Changed-Fox
The fix:
- Cmos battery was not working (dead), replace with new battery
12. Adding New Hardware Device, Tp Not Detected by BIOS
The fix:
- Chances are you already an ancient bios so it can not detect new hardware, then immediately update your bios (can be downloaded via the Internet, eg: www.windrivers.com)
13. Track Damage Card In MB
The fix:
- Try by removing and plugging a few cards on your MB
- If the boot is successful then your card is not problematic so likewise vice versa
14. Install a New Processor Tp Not Detected
The fix:
- Check whether you have installed the processor correctly denan
- Check whether the position of the jumpers on the processor is correct (about the jumpers on the processor you can Check this in the manual book)
15. Crash After Installing New RAM
The fix:
- The possibility of ram that you attach is not compatible with your computer (unplug the ram)
16. Adding RAM But Not Detected
The fix:
- Make a check as when the previous case
- Make sure the slots are used in accordance yan, for example: SD RAM has a slot similar to RAM but RD RD RAM, can not be detected although it can be installed on the slot type SD RAM.
17. After Adding RAM Computer manjadi The Slow Process
The fix:
- Note the limit of your ram capacity, such as type of EDO RAM maximum limit is 64 MB, so when forced to add it your computer becomes slow
18. Virtual Ram
The fix:
- Right-click the My Computer icon, select properties, then select the Performance tab and click on VIRTUAL MEMORY
- Select an item let me specify my own virtual memory settings (select the HD which will be used as virtual memory)
- Bell-shaped OK
19. Monitors Do Not Want Nyala
The fix:
- Make sure all power cables and connectors associated with the monitor ok
- Make sure also that there are pins on the VGA port entrance with no one crooked sempuran let alone does not make all / one pin VGA port
- Make sure your VGA card is also ok
20. Monitor Being Dark When Loading Windows
The fix:
- Probably due to setup driver for the monitor is not appropriate (frequency setting is too high)
- First entry into a state of safe mode (press F8)
- Reinstall the drivers VGA
21. Suddenly Views Damage and Computer manjadi Hang
The fix:
- Due to the temperature (in VA card) very hot
22. Display size monitor Desire Not Available
The fix:
- Go to display properties (click kana semabrang places select properties)
- Press the settings tab and adjust the size and appearance in accordance with the wishes (at screean area)
23. Monitor Blinks When Used As
The fix:
- Go to display properties (Right-click any places select properties)
- Press the tab and click advanced settings, then click the adapter, in this section show that chill refresh raet
24. New Sound Card Not Detected
The fix:
- Crash with the old card saounda
- Check the manual booknya, whether the soundcard on boardnya need to shut down or not if you want to re-install wich a new soundcard (usually can be turned off via jumper or BIOS)
1. Computers Not Want to Live
The fix:
- Check cable connection (from the power outlet to the power button on PC)
- Check whether the stabilizer function or tdak (if using the stabilizer)
- Check the power cable on CPU
- If you still do not want to live problem may lie in the power supply or MB
2. Computer Life But Not want Booting
The fix:
Know First Beep Beep:
Beep 1 time only sign that the condition of good computer
Beep 1 time, length There are problems in memory
Beep 1 time and 3 times the short-term damage on the VGA card
Beep 1 time 2 times long and short-Damage in DRAM parity
Beep continuously Damage dimodul memory or video memory
- Check with using software such as SiSoft Sandra dianosa, PC mark04, mark05 PC etc.
3. Computer Mau Booting But Always "Safe Mode" (to go into safe mode press F8)
The fix:
- Restart your computer again
- If still trouble re intall your windows
- If it still safe mode also means your HD problems
check with: scan disk
4. Computer Hangs Frequently
How to cope
- Due to software crashes
- Press ctrl + alt + del>> click End Task on the program "Not Responding"
- Press the restart button on the CPU
- Due to hardware conflict (to the addition of new hardware)
- Conflicts between hardware often occurs on windows operating system
- Re-install your windows, but keep in mind before you reinstall windows, first remove your new hardware
- Run facilities "add new" hardware found on the control panel.
5. Keyboard is not recognized by Computer
How to cope
- Check if your keyboard is properly installed
- If it already but still the keyboard is not detected then chances are your keyboard problem.
- Try to replace your keyboard, if it has been replaced but the problem persists then most likely destroyed was at the keyboard port on your MB.
- If it has been in New Keyboard Replace remain undetected but Also Try to Replace with a USB keyboard and if not detected also means there is something wrong in the Windows system Buddies
6 Mouse is not recognized by the computer (the same case With keyboard)
7. Always Jumping Mouse Pointer-Skip
How to cope
- Clean up immediately on the dirty mouse (especially on the ball mouse)
8. Computer Crashes Often
The fix:
- Check all the cable position, hardware, and also stresses on the casing, check the temperature on the CPU and likewise check ram, processor and vga.
9. If Manufacturer MetherBoard (MB) Unknown
The fix:
- Open the casing, and check your CPU is usually a MB has a label manufacturer that also contains a specification type Mb.
- Look in the manual book
- Find a Mb of data over the Internet, skewer ID which is printed on the sticker board with list contained on the site www.fcc.gov / oet / fccid, and search the list of ID numbers issued by the licensing agency for electronic device in America
- Use analysis software, such as sandra99 etc.
10. Forgot BIOS Password
The fix:
- Remove the cmos on the cpu batterey
- Or by try some guessed default passwords for some manufacturers eg AMI and AWARD BIOS (eg, AMI, AMI, AMI_SW, Ally, 589 589 etc.)
11. Clock and setting the date BIOS Always Changed-Fox
The fix:
- Cmos battery was not working (dead), replace with new battery
12. Adding New Hardware Device, Tp Not Detected by BIOS
The fix:
- Chances are you already an ancient bios so it can not detect new hardware, then immediately update your bios (can be downloaded via the Internet, eg: www.windrivers.com)
13. Track Damage Card In MB
The fix:
- Try by removing and plugging a few cards on your MB
- If the boot is successful then your card is not problematic so likewise vice versa
14. Install a New Processor Tp Not Detected
The fix:
- Check whether you have installed the processor correctly denan
- Check whether the position of the jumpers on the processor is correct (about the jumpers on the processor you can Check this in the manual book)
15. Crash After Installing New RAM
The fix:
- The possibility of ram that you attach is not compatible with your computer (unplug the ram)
16. Adding RAM But Not Detected
The fix:
- Make a check as when the previous case
- Make sure the slots are used in accordance yan, for example: SD RAM has a slot similar to RAM but RD RD RAM, can not be detected although it can be installed on the slot type SD RAM.
17. After Adding RAM Computer manjadi The Slow Process
The fix:
- Note the limit of your ram capacity, such as type of EDO RAM maximum limit is 64 MB, so when forced to add it your computer becomes slow
18. Virtual Ram
The fix:
- Right-click the My Computer icon, select properties, then select the Performance tab and click on VIRTUAL MEMORY
- Select an item let me specify my own virtual memory settings (select the HD which will be used as virtual memory)
- Bell-shaped OK
19. Monitors Do Not Want Nyala
The fix:
- Make sure all power cables and connectors associated with the monitor ok
- Make sure also that there are pins on the VGA port entrance with no one crooked sempuran let alone does not make all / one pin VGA port
- Make sure your VGA card is also ok
20. Monitor Being Dark When Loading Windows
The fix:
- Probably due to setup driver for the monitor is not appropriate (frequency setting is too high)
- First entry into a state of safe mode (press F8)
- Reinstall the drivers VGA
21. Suddenly Views Damage and Computer manjadi Hang
The fix:
- Due to the temperature (in VA card) very hot
22. Display size monitor Desire Not Available
The fix:
- Go to display properties (click kana semabrang places select properties)
- Press the settings tab and adjust the size and appearance in accordance with the wishes (at screean area)
23. Monitor Blinks When Used As
The fix:
- Go to display properties (Right-click any places select properties)
- Press the tab and click advanced settings, then click the adapter, in this section show that chill refresh raet
24. New Sound Card Not Detected
The fix:
- Crash with the old card saounda
- Check the manual booknya, whether the soundcard on boardnya need to shut down or not if you want to re-install wich a new soundcard (usually can be turned off via jumper or BIOS)
Good Luck..!!
